Search results

  1. F

    Rosewood ST1000LM035 Stays BSY after getting ready

    Hello, Yes I can execute the terminal commands and have already downloaded all of the essential SYS files.
  2. F

    Rosewood ST1000LM035 Stays BSY after getting ready

    Hello, This rosewood drive gets ready but goes to BSY as soon as I try to access any sector. below is terminal output. (P) SATA Reset RAW OFF PASS Drive AMPS Configuration has been modified from compiled defaults. Drive must be re-initialized to controller firmware defaults by...
  3. F

    DONOR with more heads than Patient where bottom head missing

    I have 10 Head Donor drive 5TB Seagate barracuda ST5000LM000. Patient drive is 4TB ST4000LM0024 which is having 9 Heads. Until now we have replaced with HSA having more heads than patient HSA but more heads were on the upper side which was all successful. This case is where the bottom head is...
  4. F

    Spyglass slow responding solution?

    Hello, Is there any solution available for spyglass slow responding issue. this issue first reported on hddguru in 2017. wondering if anyone has managed to slove it successfully. I am able to read max 60kb/s. Regards
  5. F

    Data cant be decrypted in DE Task

    Hi, I have WD Hubble 500GB WDC WD5000LMVW-11VEDS3 drive. All essential modules are ok. But 33 plist on head0 is bad in zeros. 1. Can I reduce its size in dir editor? 2. Sectors are not accessible without using utility. I can decrypt and access sectors in utility by using "use utility" option...
  6. F

    Firmware Request

    Hi Jared, Yes, Its Palmer.
  7. F

    Firmware Request

    Hi Everyone, Looking for WD10SPZX-24T10T1 firmware. ROM F/W Version 00050066. I have used unlocked SATA Pcb but getting error “VSC ERR INV FUNC CODE REQ”.
  8. F

    Seagate Grenada Preamp Tracking

    Because of difference in PreAmp?
  9. F

    Seagate Grenada Preamp Tracking

    Patient Donor SN: W1E2DFAJ W1E0S6N0 ML: ST2000DM001 ST2000DM001 PN: 9YN164-306 9YN164-306 FW: CC4H CC4H Date: 13217 12514 PreAmp: CB06 B303 Site: SU...
  10. F

    Cross Compatible WD Families

    Works perfectly fine!!
  11. F

    Cross Compatible WD Families

    Does anyone know sure compatibility between Tahoe LT and Tahoe PL? PATIENT = Tahoe LT - WD5000AAKS-00UU3A0 DCM:DGNCHTJMHN 29OCT2010 DONOR = Tahoe PL - WD5000AAKS-22V1A0 DCM:HHRNNTJCAN 26MAY2010
  12. F

    Samsung HN-M101MBB slider stuck on insde platter

    Hi Jared, are these swabs good for cleaning platter surface for fingerprints and debris?
  13. F

    Samsung HN-M101MBB slider stuck on insde platter

    Thank you all for all your reply and suggestions. Removed platters with the help of stickers, used the plastic stick to remove the slider and that's it. Drive now imaging. :D
  14. F

    Samsung HN-M101MBB slider stuck on insde platter

    I have 1TB Samsung HNM101MBB drive for data recovery. bottom 2 heads 0-1 are with out slider. After looking closely inside the platter those sliders are stuck to platters. I tried to shake the drive to remove sliders but it could not come out. Is there any way to get those out so that I can...
  15. F

    PC3OOO UDMA unusual behavior

    Thank you everyone for your valuable feedback and time spent on trying to figure out the problem with my device. My PC3KUDMA is back on track and working again without the symptom I was facing earlier. probably it was either wattage issue or just dust buildup. I removed extra 3.5" Sata hard...
  16. F

    PC3OOO UDMA unusual behavior

    I don't think Its loose connection because when I tried removing molex out of PC3K It was jammed in and I had to apply extra force to remove it.
  17. F

    PC3OOO UDMA unusual behavior

    It was weak battery which was showing these awkward results. Now after replacing battery of my DMM, readings I am getting is on the dot. 12.14 and 5.12 for 12V and 5V. So PSU is OK.
  18. F

    PC3OOO UDMA unusual behavior

    Can weak battery of multimeter cause these readings?
  19. F

    PC3OOO UDMA unusual behavior

    Measured on 24pin ATX Pins and also on molex going to PC3K.
  20. F

    PC3OOO UDMA unusual behavior

    I thought maybe power supply is faulty, so took below readings 16.63V on 12V (Yellow Wire) 7.09V on 5V (Red Wire) 4.84V on 3.3V (Orange Wire) Are these fine?
  21. F

    PC3OOO UDMA unusual behavior

    Hello, I am facing issues with my pc3kudma board sata0 port. Some times the drive don't get power, some times drives keep restarting and WD drives when connected doesn't get ID and capacity but works fine in sata1 port. I have no electronics background to diagnose the issue, but can use...
  22. F

    Seagate UltraSlim (Rosewood)1TB and 2TB Technical Reviews

    I had 2 cases, that was 1TB drive for which I am still looking for suitable donor. I didn't attempt 1TB head replacement upon your doubt that it might not work.
  23. F

    Seagate UltraSlim (Rosewood)1TB and 2TB Technical Reviews

    Hurray!! Successfully did HSA replacement of 2TB drive. Thank you Jared for your warning ! Did about 10 - 12 attempts of head replacement before actually touching donor head.
  24. F

    Seagate UltraSlim (Rosewood)1TB and 2TB Technical Reviews

    Hello Everyone, Kindly confirm, if below both HSA would be compatible or not. Both drives front label are exact same except Sr. No., WWN and Date. Want to take your expert opinion if trying head replacement will be of any use. I suspect because of density difference it might not work. Kindly...
  25. F

    Toshiba USB to SATA Guide

    USB G003189A --> SATA G003138A -- Confirmed
  26. F

    Seagate UltraSlim (Rosewood)1TB and 2TB Technical Reviews

    Hi Jared, May I ask which Head unstick tool you are using?
  27. F

    Seagate UltraSlim (Rosewood)1TB and 2TB Technical Reviews

    Thank you Jared for your advice, I do pray every time I start any recovery so that my mind stay focus and also lot of caffeine :) . Let me try and will post update.
  28. F

    Seagate UltraSlim (Rosewood)1TB and 2TB Technical Reviews

    Hello Everyone, I have 2 rosewood drive 1tb and 2 tb for head replacement. Wanting to get your valuable advice on things to remember while doing head replacement in these drives and also if these drives require adaptive parameter transfer after head replacement. I have got head tools already.
  29. F

    Is Toshiba MK4026GAX suitable head donor for MK8032GAX?

    Found out the hard way!! 40Gb has 2 heads whereas 80GB 4 heads. Trying to find exact donor :cry:
  30. F

    Is Toshiba MK4026GAX suitable head donor for MK8032GAX?

    Hi All, I got very old approx 2005 Toshiba IDE drive MK8032GAX for recovery. Exact match donor is not available. I have got only donor available which is MK4026GAX, Is this suitable mach for MK8032GAX?
  31. F

    Hitachi HTS547550A9E384 Stays BSY

    Hi Everyone, Need help in this case. Hitachi HTS547550A9E384 Stays BSY all the time. I have replaced PCB but still the same. How to make this drive go to ready state for any firmware manipulation or accessing the SA. Do I have to Short read channel? Any Solution ? Best Regards, Murtaza
Top