ST1000LM024 - HN-M101MBB - BSY

[lcoughey]

https://www.donordrives.com/catalogsear ... a30001+sc3

 

[slingshot]

Thanks Luke, on its way

 

[jol]

do you have a matching PCB ?

 

[slingshot]

I've got several that spin the drive up

 

[jol]

then flash a A ROM withe same FW using n external programmer
problem solved

 

[slingshot]

What ROM am I programming to my donor board ?

I have already tried to take the ROM with same firmware and program it to donor board, drive spins up and still stuck in BSY.

Current output from terminal:
[nfo]ActiveFW : 00
FWVer : 0001
SATA PLL cal done
DDR size detected = 16MB

DDR size detected = 16MB

*PAUNI_L2957*PA VID=0006 PN=0009 Rev=0002- PA_UNI Found
*PAUNI_L2957*PA VID=0006 PN=0009 Rev=0002- PA_UNI FoundU
S_0:49
SO_1
SPU@34'C,4951mV
IS=5
CLA ..36/59
HO..OK
HO RPM=1617 OK
AC 1109
ST..OK
mS1 00000003
GT:432
SC(L):4169/93
BE.N:33
LD..OK
SK C: 7383 H:0
Boot Sector Error!
Error to read FIT header ( 0: 0: 1)
Error to read FIT header ( 0: 1: 1)
Error to read FIT header ( 0: 2: 1)
Use default FIT
| 0 | FSI | 0 | 0 | 22 | 1340 |
| 0 | FSI | 0 | 1 | 22 | 1340 |
| 0 | FSI | 0 | 2 | 22 | 1340 |
| 0 | FSI | 42 | 0 | 22 | 1340 |
| 0 | FSI | 42 | 1 | 22 | 1340 |
| 0 | FSI | 42 | 2 | 22 | 1340 |
| 4 | MLIST | 0 | 0 | 10 | 1340 |
| 4 | MLIST | 0 | 1 | 10 | 1340 |
| 4 | MLIST | 0 | 2 | 10 | 1340 |
| 4 | MLIST | 42 | 0 | 10 | 1340 |
| 4 | MLIST | 42 | 1 | 10 | 1340 |
| 4 | MLIST | 42 | 2 | 10 | 1340 |
| 155 | SV_TBL | 0 | 0 | 23 | 1340 |
| 155 | SV_TBL | 0 | 1 | 23 | 1340 |
| 155 | SV_TBL | 0 | 2 | 23 | 1340 |
| 155 | SV_TBL | 42 | 0 | 23 | 1340 |
| 155 | SV_TBL | 42 | 1 | 23 | 1340 |
| 155 | SV_TBL | 42 | 2 | 23 | 1340 |
| 181 | RESO_TBL | 0 | 0 | 35 | 1340 |
| 181 | RESO_TBL | 0 | 1 | 35 | 1340 |
| 181 | RESO_TBL | 0 | 2 | 35 | 1340 |
| 106 | BUMP_LIM | 58 | 0 | 0 | 1340 |
| 106 | BUMP_LIM | 58 | 1 | 0 | 1340 |
| 106 | BUMP_LIM | 58 | 2 | 0 | 1340 |
| 180 | RR0_TBL | 0 | 0 | 33 | 1340 |
| 180 | RR0_TBL | 0 | 1 | 33 | 1340 |
| 180 | RR0_TBL | 0 | 2 | 33 | 1340 |
| 180 | RR0_TBL | 42 | 0 | 33 | 1340 |
| 180 | RR0_TBL | 42 | 1 | 33 | 1340 |
| 180 | RR0_TBL | 42 | 2 | 33 | 1340 |
| 12 | CHN_TBL | 0 | 0 | 46 | 1340 |
| 12 | CHN_TBL | 0 | 1 | 46 | 1340 |
| 12 | CHN_TBL | 0 | 2 | 46 | 1340 |
| 12 | CHN_TBL | 42 | 0 | 46 | 1340 |
| 12 | CHN_TBL | 42 | 1 | 46 | 1340 |
| 12 | CHN_TBL | 42 | 2 | 46 | 1340 |
| 13 | GEO_TBL | 0 | 0 | 142 | 1340 |
| 13 | GEO_TBL | 0 | 1 | 142 | 1340 |
| 13 | GEO_TBL | 0 | 2 | 142 | 1340 |
| 13 | GEO_TBL | 42 | 0 | 142 | 1340 |
| 13 | GEO_TBL | 42 | 1 | 142 | 1340 |
| 13 | GEO_TBL | 42 | 2 | 142 | 1340 |
| 157 | PARAM_DM | 0 | 0 | 260 | 1340 |
| 157 | PARAM_DM | 0 | 1 | 260 | 1340 |
| 157 | PARAM_DM | 0 | 2 | 260 | 1340 |
Fw Active 00
| 115 | MOVLY001 | 1 | 0 | 10 | 1340 |
| 115 | MOVLY001 | 1 | 1 | 10 | 1340 |
| 115 | MOVLY001 | 1 | 2 | 10 | 1340 |
Overlay file read bad[/nfo]

 

[jol]

[post]15232[/post] What ROM am I programming to my donor board ?

2BA30001
https://files.hddguru.com/download/PC-3 ... F709521.7z

https://files.hddguru.com/download/Non- ... C94487.rar

 

[slingshot]

Just used the 3000 to upload the ROM into it and now terminal is complaining with this

[nfo]ActiveFW : 00
FWVer : 0001
SATA PLL cal done
FW - Chip mismatch ![/nfo]

 

[jol]

[post]15234[/post] Just used the 3000

I said external programmer

 

[slingshot]

I'll use the external programmer tomorrow and see if I can get one of those ROM's into the PCB.